BSS Audio BLU-120 Signal Processor
Networked I/O expander with fault-tolerant bus chassis (no
CobraNet™) - requires up to four input / output cards
KEY FEATURES:
- Four Input / Output Card Slots
- Configurable Inputs / Outputs
- Analog Inputs (with Phantom Power per Channel)
- Analog Outputs
- Digital Inputs (AES/EBU and S/PDIF)
- Digital Outputs (AES/EBU and S/PDIF)
- Rich Palette of Logic Objects
- 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus
- Clear Front Panel LED Indication
- Informative Front Panel Display
- Bi-Directional Locate Functionality
- 12 Control Inputs and 6 Logic Outputs for GPIO Integration
- Soundweb London Interface Kit for Third Party Control System Integration (Documentation)
- HiQnet Device
- Configuration, Control and Monitoring from HiQnet London Architect
Front Panel Led Indicators:
Per Input: Signal Present, CLIP, SYNC/48V, I/O card type (IN, OUT, DIG, AEC(BLU-800, 320, 160, 120))
Other: LCD Display, Conductor active†, Net Link active†, Data Activity, †(BLU-800, 320, 80, 32)
Analog Inputs: Up to 16 electronically balanced on Phoenix Combicon removable screw connectors
Mic/Line Inputs: Nominal gain 0dB, electronically switchable up to +48dB,in +6dB steps
Input Impedance: 3.5k?
Maximum Input Level: +20dBu with 0dB input gain,+8dBu with 12dB gain
CMRR: >75dB at 1KHz
Input Noise (E.I.N.): <-128dBu typical with 150? source
Phantom Power: 48V nominal, selectable per input
A/D Latency: 38.7/Fs
Digital Inputs: Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Input Impedance: 110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate: 48kHz or 96kHz
Sample Rate Conversion: 8kHz-96kHz
THD+N: <-140dB
Latency: 3/Fso + (56.581/Fsi) + (55.658/Fso)
Analog Outputs: Up to 16 electronically balanced on Phoenix/Combicon removable screw connectors
Maximum Output Level: +19dBu
Frequency Response: 20Hz-20KHz (+0.5dB/-1dB)
THD: <0.01% 20Hz to 20KHz, +10dBu output
Dynamic Range: 108dB typical, 22Hz-22KHz unweighted
Crosstalk: <-75dB
D/A Latency: 28/Fs
Digital Outputs: Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Output Impedance: 110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate: 48kHz or 96kHz
Sample Rate Conversion: 8kHz-96kHz
THD+N: <-140dB
Latency: 3/Fso + (56.581/Fsi) + (55.658/Fso)
Control Ports: 12 inputs and 6 outputs
Control Input Voltage: 0 to 4.5v
Control Input Impedance: 4.7k? to +5V (2-wire mode), >1M? (3-wire mode)
Logic Output Voltage: 0 or +5V unloaded
Logic Output Impedance: 440?s
Logic Output Current: 10mA source, 60mA sink
Watchdog Output: Phoenix/Combicon connector for failsafe control
Opto Output Current: 14mA maximum
Withstanding Voltage: 80V maximum (Off)
Series Impedance: 220? (isolated)
Control Network (All Models):
Connectors: RJ45 Ethernet connector
Maximum Cable Length: 100m/300ft on Category 5e cable between device and Ethernet switch
Digital Audio Bus (BLU-800, BLU-320, BLU-160, BLU-120):
Connectors: 2 x RJ45 Ethernet connectors
Maximum Cable Length: 100m/300ft on Category 5e cable between devices
Maximum Number of Nodes: 32
Latency Per Node: 4(+/-1)Fs
CobraNet™ Audio Network (BLU-800, BLU-320, BLU-80, BLU-32 only):
Connectors: 2 x RJ45 connectors
Maximum Cable Length: 100m/300ft on Category 5 cable between device and Ethernet switch
Power and Dimensions †† (BLU-800, BLU-320, BLU-160, BLU-120), ††† (BLU-80, BLU-32, BLU-16):
Mains Voltage: 100-240V AC, 50/60Hz
Power Consumption: <35VA
BTU Rating: <188 BTU/hr †† ; <120 BTU/hr †††
Operating Temperature Range: 5(41) to 35(95) degrees C(degrees F)
Dimensions (H(U) x W x D): 1.75" (1U) x 19" x 12.5" †† / 9” ††† (45mm x 483mm x 318mm †† / 228mm †††)
Weight: 9 lbs †† / 4.1 kgs †† (estimated); 7.3 lbs ††† / 3.3 kgs ††† (estimated)
.png)
.png)